M5×0.5 Thread Dimensions and Tap Drill
M5×0.5 is an ISO metric fine-pitch thread: the 5 mm diameter with a 0.5 mm pitch (50.8 threads per inch) instead of the coarse 0.8 mm of M5×0.8. The thread is 0.16 mm shallower, so the tensile stress area rises from 14.2 to 16.1 mm² (14% more) and the lead angle falls from 3.25° to 1.95°.
- Tap drill4.5 mm77% thread
- Pitch0.5 mm50.8 TPI
- Major diameter5.000 mm0.1969 in
- Pitch diameter4.675 mm0.1841 in
- Minor diameter (nut)4.459 mm0.1755 in
- Tensile stress area16.1 mm²0.0250 in²
- Clearance hole5.5 mmmedium fit, ISO 273
Thread profile
M5×0.5 basic dimensions
| Dimension | mm | in |
|---|---|---|
| Major diameter d = D | 5.000 | 0.1969 |
| Pitch P | 0.500 | 0.0197 |
| Pitch diameter d2 = D2 | 4.675 | 0.1841 |
| Minor diameter, internal thread D1 | 4.459 | 0.1755 |
| Minor diameter, external thread d3 | 4.387 | 0.1727 |
| Height of fundamental triangle H | 0.433 | 0.0170 |
| Thread height, internal (5H/8) | 0.271 | 0.0107 |
| Thread height, external (17H/24) | 0.307 | 0.0121 |
| Crest flat of external thread (P/8) | 0.062 | 0.0025 |
| Crest flat of internal thread (P/4) | 0.125 | 0.0049 |
| Property | Value |
|---|---|
| Threads per inch | 50.80 |
| Flank angle | 60° (30° each side) |
| Lead angle at the pitch diameter | 1.95° |
| Tensile stress area As | 16.1 mm² (0.0250 in²) |
Basic (nominal) sizes per ISO 724, before tolerances. d3 is the root diameter of a bolt with the rounded root that ISO 898-1 uses for the stress area.
M5×0.5 tolerance limits (6g bolt, 6H nut)
6g and 6H are the general-purpose tolerance classes for commercial screws and nuts. The 6g screw has a fundamental deviation of 20 µm, so even at its largest it sits 0.020 mm below the basic size and leaves room for a thin plating.
| External thread 6g | Max (mm) | Min (mm) | Tolerance (mm) |
|---|---|---|---|
| Major diameter d | 4.980 | 4.874 | 0.106 |
| Pitch diameter d2 | 4.655 | 4.580 | 0.075 |
| Internal thread 6H | Max (mm) | Min (mm) | Tolerance (mm) |
|---|---|---|---|
| Minor diameter D1 | 4.599 | 4.459 | 0.140 |
| Pitch diameter D2 | 4.775 | 4.675 | 0.100 |
Computed from the ISO 965-1 deviations and tolerances for normal length of engagement; the results match the limits tabulated in ISO 965-2.
M5×0.5 tap drill size
Tap drill for M5×0.5: 4.5 mm
This leaves about 77% thread in the tapped hole.
The rule for metric tap drills is diameter minus pitch: 5 − 0.5 = 4.5 mm, which is a stocked drill size.
The 6H minor diameter of the finished nut thread must lie between 4.459 and 4.599 mm. The recommended drill falls inside that band.
Other drills that work for M5×0.5
A larger drill cuts less thread and taps more easily; a smaller one gives a fuller thread but loads the tap harder.
| Drill | mm | in | % thread | Within 6H limits | Thread engagement |
|---|---|---|---|---|---|
| #16 (0.1770 in) | 4.50 | 0.1770 | 78% | yes | |
| 4.5 mmrecommended | 4.50 | 0.1772 | 77% | yes | |
| 4.6 mm | 4.60 | 0.1811 | 62% | no |
% thread = (major diameter − drill diameter) ÷ (1.299 × pitch). See the tap drill chart for how to choose a percentage.
Clearance hole for M5
The clearance hole depends only on the 5 mm diameter, not on the pitch. The medium series, 5.5 mm, is the usual choice for general assembly.
| Series | Hole Ø (mm) | Hole Ø (in) | Clearance on Ø (mm) |
|---|---|---|---|
| Fine (H12) | 5.3 | 0.2087 | 0.3 |
| Medium (H13) | 5.5 | 0.2165 | 0.5 |
| Coarse (H14) | 5.8 | 0.2283 | 0.8 |
Hole diameters from ISO 273.
M5×0.5 strength
ISO 898-1 tabulates fine-pitch loads only for a selected set of threads from M8×1 to M39×3, so it gives no proof or breaking loads for M5×0.5. For an estimate, multiply the tensile stress area of 16.1 mm² by the stress of the material: for example, 800 MPa gives 12.9 kN.
M5 pitches compared
All standard pitches on the M5 diameter. A finer pitch gives a shallower thread, a larger core and a smaller lead angle; a coarser pitch is faster to assemble and more tolerant of damage and plating.
| Thread | Pitch (mm) | Pitch Ø (mm) | Minor Ø D1 (mm) | Stress area (mm²) | Tap drill |
|---|---|---|---|---|---|
| M5×0.8 | 0.8 | 4.480 | 4.134 | 14.2 | 4.2 mm |
| M5×0.5 | 0.5 | 4.675 | 4.459 | 16.1 | 4.5 mm |
Closest inch thread
No inch thread is interchangeable with M5×0.5. The nearest is #10-32 UNF, which is 0.17 mm smaller in diameter with a pitch of 0.794 mm against 0.500 mm. A nut may start on the wrong thread and then bind or strip, so identify by both diameter and pitch.
| Thread | Major Ø (mm) | Pitch (mm) | TPI | Ø difference (mm) |
|---|---|---|---|---|
| M5×0.5 (this thread) | 5.000 | 0.500 | 50.80 | — |
| #10-32 UNF | 4.826 | 0.794 | 32.00 | -0.174 |
| #10-24 UNC | 4.826 | 1.058 | 24.00 | -0.174 |
How the M5×0.5 dimensions are calculated
Every basic dimension follows from the major diameter and the pitch:
- P = 0.5 mm
- H = 0.866025 × P = 0.433 mm
- d2 = d − 0.649519 × P = 5 − 0.325 = 4.675 mm
- D1 = d − 1.082532 × P = 5 − 0.541 = 4.459 mm
- d3 = d − 1.226869 × P = 5 − 0.613 = 4.387 mm (external root, 17H/24 deep)
- As = π/4 × ((d2 + d3) ÷ 2)² = π/4 × 4.531² = 16.12 mm²
- Lead angle = arctan(P ÷ (π × d2)) = 1.95°
Related sizes and tools
Sources: ISO 68-1 and ISO 724 (profile and basic dimensions), ISO 261 (diameter and pitch series), ISO 965-1 (tolerances), ISO 273 (clearance holes), ISO 898-1 (mechanical properties) and tap drill tables based on ISO 2306. How this site checks its data. Last reviewed 29 September 2026.