#10-32 UNF Thread Dimensions and Tap Drill
#10-32 UNF is the Unified fine thread for the number 10 size (major diameter 0.190 in, 4.83 mm): 32 threads per inch, a pitch of 0.03125 in (0.794 mm), on a 60° profile. ASME B1.1 lists it in the UNF series. Against the coarse #10-24 UNC it has 32 threads per inch instead of 24, a stress area 14% larger and a lead angle of 3.35° instead of 4.65°.
#10-32 is the traditional 19 inch rack screw, the green grounding screw in electrical boxes and a standard thread for small pneumatic fittings.
- Tap drill#2176% thread, 4.04 mm
- Pitch32 TPI0.794 mm
- Major diameter0.1900 in4.826 mm
- Pitch diameter0.1697 in4.310 mm
- Minor diameter (nut)0.1562 in3.967 mm
- Tensile stress area0.0200 in²12.9 mm²
- Clearance hole#2normal fit, ASME B18.2.8
Thread profile
#10-32 UNF basic dimensions
| Dimension | in | mm |
|---|---|---|
| Major diameter d = D | 0.1900 | 4.826 |
| Pitch P | 0.03125 | 0.794 |
| Pitch diameter d2 = D2 | 0.1697 | 4.310 |
| Minor diameter, internal thread D1 | 0.1562 | 3.967 |
| Minor diameter, external UNR thread d3 | 0.1528 | 3.881 |
| Height of fundamental triangle H | 0.0271 | 0.687 |
| Thread height, internal (5H/8) | 0.0169 | 0.430 |
| Thread height, external (11H/16) | 0.0186 | 0.473 |
| Crest flat of external thread (P/8) | 0.0039 | 0.099 |
| Crest flat of internal thread (P/4) | 0.0078 | 0.198 |
| Property | Value |
|---|---|
| Threads per inch | 32 |
| Flank angle | 60° (30° each side) |
| Lead angle at the pitch diameter | 3.35° |
| Tensile stress area As | 0.0200 in² (12.9 mm²) |
Basic (nominal) sizes per ASME B1.1, before tolerances. A UN external thread with a flat root has the same basic minor diameter as the nut (D1); d3 applies to the rounded UNR root.
#10-32 UNF limits of size (class 2A bolt, 2B nut)
Classes 2A and 2B are the general-purpose fits for commercial bolts, screws and nuts. The 2A external thread has an allowance of 0.0009 in, so its maximum size is that much below basic; the 2B nut starts at the basic size.
| External thread 2A | Max (in) | Min (in) | Tolerance (in) |
|---|---|---|---|
| Major diameter | 0.1891 | 0.1831 | 0.0060 |
| Pitch diameter | 0.1688 | 0.1658 | 0.0030 |
| Internal thread 2B | Max (in) | Min (in) | Tolerance (in) |
|---|---|---|---|
| Minor diameter | 0.164 | 0.156 | 0.0080 |
| Pitch diameter | 0.1736 | 0.1697 | 0.0039 |
Limits of size from ASME B1.1 Table 2.
#10-32 UNF tap drill size
Tap drill for #10-32 UNF: #21 (0.1590 in, 4.04 mm)
This leaves about 76% thread in the tapped hole.
#21 is the drill listed for #10-32 UNF in standard tap drill charts. It is 0.0310 in under the 0.1900 in major diameter.
The 2B minor diameter of the finished nut thread must lie between 0.156 and 0.164 in. The recommended drill falls inside that band.
Other drills that work for #10-32 UNF
A larger drill cuts less thread and taps more easily; a smaller one gives a fuller thread but loads the tap harder.
| Drill | mm | in | % thread | Within 2B limits | Thread engagement |
|---|---|---|---|---|---|
| #23 | 3.91 | 0.1540 | 89% | no | |
| 5/32" | 3.97 | 0.1562 | 83% | yes | |
| #22 | 3.99 | 0.1570 | 81% | yes | |
| 4 mm | 4.00 | 0.1575 | 80% | yes | |
| #21recommended | 4.04 | 0.1590 | 76% | yes | |
| #20 | 4.09 | 0.1610 | 71% | yes | |
| #19 | 4.22 | 0.1660 | 59% | no | |
| #18 | 4.31 | 0.1695 | 50% | no |
% thread = (major diameter − drill diameter) ÷ (1.299 × pitch). See the tap drill chart for how to choose a percentage.
Clearance hole for #10
The clearance hole depends only on the 0.1900 in diameter, not on the thread series. The normal fit, a #2 drill, is the usual choice for general assembly.
| Fit | Drill | Hole Ø (in) | Hole Ø (mm) | Clearance on Ø (in) |
|---|---|---|---|---|
| Close | #5 | 0.2055 | 5.22 | 0.0155 |
| Normal | #2 | 0.2210 | 5.61 | 0.0310 |
| Loose | B | 0.2380 | 6.05 | 0.0480 |
Nominal drill sizes from ASME B18.2.8.
#10-32 UNF strength
SAE J429 starts at 1/4 in, so the SAE grades give no proof load for #10-32 UNF. For an estimate, multiply the tensile stress area of 0.0200 in² by the strength of the material: for example, 60,000 psi gives 1,200 lbf.
#10 pitches compared
All standard pitches on the #10 diameter. A finer pitch gives a shallower thread, a larger core and a smaller lead angle; a coarser pitch is faster to assemble and more tolerant of damage and plating.
| Thread | TPI | Pitch Ø (in) | Minor Ø D1 (in) | Stress area (in²) | Tap drill |
|---|---|---|---|---|---|
| #10-24 UNC | 24 | 0.1629 | 0.1449 | 0.0175 | #25 |
| #10-32 UNF | 32 | 0.1697 | 0.1562 | 0.0200 | #21 |
Closest metric thread
No metric thread is interchangeable with #10-32 UNF. The nearest is M5×0.8, which is 0.17 mm larger in diameter with a pitch of 0.800 mm against 0.794 mm. A nut may start on the wrong thread and then bind or strip, so identify by both diameter and pitch.
How the #10-32 UNF dimensions are calculated
Every basic dimension follows from the major diameter and the pitch:
- P = 0.03125 in = 1 ÷ 32 threads per inch
- H = 0.866025 × P = 0.0271 in
- d2 = d − 0.649519 × P = 0.1900 − 0.0203 = 0.1697 in
- D1 = d − 1.082532 × P = 0.1900 − 0.0338 = 0.1562 in
- d3 = d − 1.190785 × P = 0.1900 − 0.0372 = 0.1528 in (external root, 11H/16 deep)
- As = 0.7854 × (d − 0.9743 × P)² = 0.7854 × 0.1596² = 0.01999 in²
- Lead angle = arctan(P ÷ (π × d2)) = 3.35°
Related sizes and tools
Sources: ASME B1.1 (profile, series, limits of size and stress area), ASME B18.2.8 (clearance holes), SAE J429 (mechanical properties) and the tap drill tables of Machinery’s Handbook. How this site checks its data. Last reviewed 29 September 2026.